Unit conversion

Home

Convert length, distance and weight between the units you meet most often. Pick the pair you need, enter the value, and keep the unit written next to the result.

5 tools in this category

Pick the tool that matches your task

Pounds to kilograms

Convert between pounds and kilograms in either direction.

Open tool

Inches to centimetres

Convert lengths between inches and centimetres.

Open tool

Miles to kilometres

Convert distances between miles and kilometres.

Open tool

Feet to metres

Convert heights and lengths between feet and metres.

Open tool

Millimetres to centimetres

Convert small measurements between millimetres and centimetres.

Open tool

Converting length and weight without introducing errors

Unit conversion is arithmetic, so the tool will not get the multiplication wrong. Almost every real mistake happens on either side of the calculation: using a figure that was already rounded, converting a measurement that was never accurate, or writing the result down without saying which unit it is in. These are habits rather than maths problems.

Pounds and kilograms in everyday comparisons

Weights quoted in pounds appear constantly in shipping limits, luggage allowances, equipment specifications and fitness figures. Converting them lets you compare like with like against a metric figure. When a limit is involved, be careful at the boundary: a value that converts to just under an allowance is not the same as one comfortably below it, and scales disagree by more than you would like.

Inches and centimetres in product dimensions

Screens, furniture, frames, clothing and shelving are all quoted in inches in some markets and centimetres in others. Convert before you compare, and watch which dimension is being described: a screen size is a diagonal, not a width, so converting it tells you nothing about whether the thing fits your desk. Check what the number measures before converting it.

Feet and metres in plans and spaces

Room dimensions, ceiling heights and site plans move between feet and metres depending on who drew them. The common trap is the mixed figure: a measurement written as feet and inches is not a decimal number of feet, and treating it as one introduces a sizeable error. Resolve it into a single unit first, then convert.

Miles and kilometres for reading distances

Distances in travel notes, race descriptions and vehicle specifications switch between miles and kilometres freely. For rough orientation a mile is a bit over one and a half kilometres, which is enough to judge whether a route is walkable. For anything you are planning around rather than just picturing, convert properly instead of relying on the mental approximation.

Millimetres and centimetres for small measurements

Technical drawings, hardware specifications and manufacturing tolerances are usually expressed in millimetres precisely because the detail matters. The conversion itself is trivial, which is exactly why it gets written down carelessly, and a misplaced decimal point here produces an error of a factor of ten. Record the unit next to the number every time.

Rounding does not improve a measurement

Converting a figure cannot make it more accurate than the original. If a length was measured to the nearest centimetre, presenting the converted value with four decimal places implies a precision that was never there. Round the result to match the accuracy of your input, and keep the raw measurement if anyone might need to recheck it.

Length, area and volume behave differently

Converting an area or a volume is not the same as converting a length, because the conversion factor applies to each dimension. Doubling a length quadruples an area and multiplies a volume by eight, which is why using a length factor on a square or cubic measurement produces an answer that is wrong by a lot rather than a little. Confirm which kind of quantity you are holding.

A quick way to check your own work

Before trusting a result, ask whether the number moved in the sensible direction. Converting inches to centimetres should give a bigger number; converting pounds to kilograms should give a smaller one. This catches the most common error of all, which is running the conversion the wrong way round, and it takes a second.

Recording measurements so they stay usable

Write the unit with every number, and state the source when it matters: measured on site, taken from a datasheet, converted from a supplier figure. A column of numbers with no units is worthless a week later, and a converted value with no record of its original is impossible to verify. Keep both, especially on anything someone else will act on.

When precision actually matters

For a rough sense of scale, an approximation is fine. For something that will be cut, ordered, shipped or submitted, use the exact conversion and the original measurement together. The cost of a careless rounding is not visible at the moment you make it; it shows up when the part does not fit or the parcel exceeds the limit.

Browse other categories

Scroll to Top