Converting millimeters to centimeters and vice versa

mm ↔ cm converter

Your result will appear here
1 centimeter = 10 millimeters

This converter moves a single measurement between millimetres and centimetres, which is the job you need whenever one set of figures is written in mm and another in cm. Enter the value, choose the direction, and read the result in the unit you want. The notes below explain the arithmetic so you can check any result by hand.

It is the everyday conversion for ruler readings, material thicknesses, hardware specifications and the dimensions of small parts. Keep one distinction in mind: converting a unit restates a measurement, it does not improve it. The tool cannot tell whether the original number was measured carefully, and it will not infer a dimension you did not enter.

How to use the converter

  1. Type the measurement into the Value field, then set From to millimetres and To to centimetres.
  2. Press Convert or the Enter key. The result appears with its unit named, so you can check it before copying.
  3. Use the swap button to reverse the direction. Your entered value stays as it is and is read in the new unit, so convert again to refresh the result.
  4. The Decimals button cycles the number of decimal places shown. Copy result puts the figure on your clipboard, and Clear empties the field to start again.

The formula, both directions

The whole calculation rests on one fixed relationship: 1 centimetre = 10 millimetres. Nothing about that changes; the only thing the tool varies is how many decimal places it displays.

centimetres = millimetres ÷ 10
millimetres = centimetres × 10

Working by hand, divide or multiply first and round at the end. Rounding early, then multiplying, is what produces results that disagree with each other across a list of measurements.

Worked examples

To convert 25 mm to centimetres, divide by 10: the answer is 2.5 cm. To convert 3.7 cm to millimetres, multiply by 10: the answer is 37 mm. In both cases only the number on the page changes, while the physical length stays exactly the same.

Use a second example to confirm you are going the right way: 12.5 cm is 125 mm. If your result came out as 1.25, the conversion ran in the opposite direction to the one you wanted.

Quick reference table

These values are exact, since dividing by ten simply shifts the decimal point. Use the formula or the tool for anything not listed here.

MillimetresCentimetres
10.1
50.5
101
252.5
505
10010
1000100

Where this actually matters

Reading a ruler is the classic case. A measurement of 46 mm is 4.6 cm, not 4.06 cm, and that kind of slip is easy to make when you are copying numbers quickly. In practical work a few millimetres can decide whether a part fits, so transfer the full measurement first and round only at the end.

Always keep the unit next to the number when you put a result into a message, a table or an order. A bare figure invites the reader to assume the unit, usually the one they were already thinking in. If you are comparing or adding two measurements, convert them to the same unit before doing anything else.

This converts length, not area or volume

Millimetres and centimetres are metric units of length, and one centimetre contains ten millimetres. Square millimetres and square centimetres are units of area and do not share that ratio: there are a hundred square millimetres in a square centimetre. This tool handles length only, so do not use it on areas or volumes.

Precision, decimal marks and common mistakes

The display shows two decimal places by default and lets you choose between none and four. Adding places does not make your measurement more precise. If the source was rounded to the nearest millimetre, no amount of displayed detail turns it into a finer reading, so keep the original value when you move data between tools.

Write the decimal mark as a full stop, as in 1.5. A comma in a figure like 1,000 is read as a thousands separator rather than a decimal mark, which is a frequent source of results that are out by a factor of a thousand. If in doubt, drop the separators and type 1000 or 1.5.

If you see an invalid-input message, remove any unit name or stray symbol and check the value is not negative. The field takes a single number, so an expression such as 5+2 or a range such as 10-15 will not work: calculate it first and enter the result. Zero is a valid entry; an empty field is not a measurement.

Frequently asked questions

Can it convert centimetres to millimetres as well?

Yes. Change the From and To lists, or press the swap button, then convert again so the result matches the new direction.

Why does my result differ slightly from another source?

Almost always rounding. Compare the number of decimal places on both sides, and make sure the original measurement really is identical before concluding that one of the two is wrong.

Can I convert several values at once?

Not in this interface, which handles one value per conversion. For a long list, keep the original and the converted figure side by side in your own table as you work through it.

Are zero and decimal values supported?

Yes, zero and any non-negative decimal are accepted. Enter the number on its own, as in 2.5, without a unit name or extra text in the field.

Scroll to Top